Human interferon alpha (IFN-α) enzyme-linked immunoassay kit instruction manual

Human interferon- α (IFN- α ) enzyme-linked immunosorbent assay

Kit instruction manual

This kit is for research use only.

examination range:                                                            96T

1μg/L - 32μg/L

purpose of usage:

The kit for determination of human serum, plasma and other biological fluids interferon [alpha] (IFN- α) content.

Experimental principle

[Alpha] Determination of human interferon samples (IFN- α) This kit double antibody sandwich method. With purified human interferon [alpha] (IFN- α) antibody-coated microtiter plate wells the immobilized antibody, monoclonal antibody-coated wells were added interferon [alpha] (IFN- α), then with HRP-labeled [alpha] The interferon (IFN- α ) antibody binds to form an antibody - antigen - enzyme - labeled antibody complex, which is thoroughly washed and then added to the substrate TMB for color development. TMB in HRP enzyme blue, yellow and eventually converted to the action of an acid. The color depth is positively correlated with alpha interferon (IFN- α ) in the sample . Then determined by comparing the absorbance (OD) at 450nm wavelength, the sample is calculated human interferon [alpha] (IFN- α) concentration of the standard curve.

Kit composition

1

30 times concentrated washing solution

20ml × 1 bottle

7

Stop solution

6ml × 1 bottle

2

Enzyme standard reagent

6ml × 1 bottle

8

Standard ( 64 μg/L )

0.5ml × 1 bottle

3

Enzyme label coated plate

12 × 8 pieces of hole

9

Standard dilution

1.5ml × 1 bottle

4

Sample diluent

6ml × 1 bottle

10

Instruction manual

1 copy

5

Developer A solution

6ml × 1 bottle

11

Sealing film

2 sheets  

6

Developer B solution

6ml × 1 / bottle

12

sealed bag

1

Specimen requirements

1 . The specimens should be extracted as soon as possible after collection, and the extraction should be carried out according to the relevant literature. The experiment should be carried out as soon as possible after extraction. If you can't test it right away, you can put the specimen in -20 °C Save, but should avoid repeated freezing and thawing

2. Samples containing NaN3 could not be detected because NaN3 inhibited horseradish peroxidase ( HRP ) activity.

Steps

1.          Dilution of Standards: This kit provides a standard of the original standard, which can be diluted in a small tube according to the following chart.

32μg/L

Standard No. 5

Add 150 μl of standard dilution to 150 μl of the original standard

16μg/L

Standard No. 4

150μl No. 5 standard Standard dilution was added 150μl

8μg/L

Standard No. 3

150μl of 4 standards Standard dilution was added 150μl

4μg/L

Standard 2

150μl standard No. 3 Standard dilution was added 150μl

2μg/L

Standard No. 1

150 μl of Standard 2 is added to 150 μl of standard dilution

2.          Adding samples: blank holes (the blank control wells are not added with the sample and the enzyme standard reagent, the other steps are the same), the standard holes, and the sample holes to be tested. Coated ELISA plates were standard accurate pipetting 50 μl, the sample holes before adding the sample dilution 40 μ l, was then combined with the test sample 10 μ l (final dilution is 5-fold). Add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, and shake gently to mix.

3.          Incubation: sealing with a sealing film 37 °C Incubated for 30 minutes.   

4.          Solution: 30 times concentrated washing solution diluted with distilled water 30 times and used

5.          Washing: Carefully remove the sealing film, discard the liquid, dry it, fill each well with the washing solution, let stand for 30 seconds, then discard it, repeat 5 times, and pat dry.

6.          Add enzyme: 50 μl of enzyme labeling reagent was added to each well , except for blank wells.

7.          Incubation: The operation is the same as 3 .

8.          Washing: The operation is the same as 5 .

9.          Color development: add 50 μl of the developer to each well , then add 50 μl of the developer , gently shake and mix. 37 °C Protected from light for 15 minutes .

10.      Termination: 50 μl of stop solution was added to each well to terminate the reaction (when the blue color turned yellow).

11.      Measurement: The absorbance ( OD value) of each well was measured in sequence with a blank air conditioner of zero and a wavelength of 450 nm . The measurement should be carried out within 15 minutes after the addition of the stop solution .

Precautions

1 . The kit should be taken out from the refrigerated environment and should be used at room temperature for 15-30 minutes before use. If the enzyme label is unsealed after opening, the slats should be stored in a sealed bag.

2 . Concentrated washing liquid may crystallize out. When diluted, it can be heated and dissolved in a water bath. The washing will not affect the result.

3 . The sampler should be used for each step, and the accuracy should be corrected frequently to avoid test errors. It is best to control the loading time within 5 minutes. If the number of specimens is large, it is recommended to use a gun.

4.   Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the substance to be tested in the specimen is too high (the OD value of the sample is larger than the OD value of the first hole of the standard well ), please first dilute the sample dilution with a certain multiple ( n times) and then measure it. When calculating, multiply the total dilution by the total dilution. Multiple ( × n × 5 ).

5.   The sealing film is intended for single use only to avoid cross-contamination.

6 . Please keep the substrate away from light.

7 . Strictly follow the instructions of the manual, the test results must be based on the microplate reader reading .

8 . All samples, washings and various wastes should be treated as infectious materials.

9 . The different batch components of this reagent must not be mixed.

10. If it is different from the English manual, the English manual shall prevail.

Storage conditions and expiration date

1 . Kit storage: 2 -8 °C .

2 . Validity: 6 months.

Fresh Garlic

Jinxiang Garlic is harvested in June each year, and our factory has an annual supply capacity of 5,000 MTS, which is available throughout the year.
High season: The last ten days from June to August. The refrigerated delivery period is from September to May.
The characteristics of Jinxiang high-quality garlic are: thick and bright skin, strong overall, plump bulbs.
Export standards and quality:
1. No tooth root, clean, no black mold, no rupture,
2. No cracks on the skin, no internal germination and growth, no insects or fungi.
Packing


Storing Fresh Garlic,Garlic Powder To Fresh Garlic,Fresh Garlic To Garlic Powder,Fresh Garlic Cloves

Jining Yuanheng International Trading Co.,Ltd , https://www.china-garlic-exporter.com

Posted on